L 70270 FL EN User manual
Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsExtra Silent95° - ColdWhite and colouredcotton with normalsoil.max. 7 kgWa
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCurtains40° - ColdSet this programmeto wash curtains. Itadds automatically
7) STANDARD PROGRAMMES for the Energy Label consumption values. According toregulation 1061/2010, these programmes are respectively the «standard 60°
Off Mode (W) Left On Mode (W)0.48 0.48The information given in the charts above are in compliance with the EU Com-mission regulation 1015/2010 impleme
9.2 Filling the detergent and additivesThe detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent
3.To use powder detergent, turn theflap up.4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or t
2.Press button 1 again to activatethe appliance. Now, you can set anew washing programme.The appliance does not drain thewater.9.6 Change a functionYo
2.Press the Start/Pause button 4 .The appliance drain the water andspin.3.When the programme is completedand the door lock symbol goes off,you can ope
• mmol/l (millimol for each litre - inter-national unit for the hardness of wa-ter).• Clarke degrees.Water hardness tableLevel TypeWater hardness°dH °
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
11.5 DrumRegularly examine the drum to preventlimescale and rust particles.Only use special products to remove rustparticles from the drum.To do this:
WARNING!1.Disconnect the mains plugfrom the mains socket.2.Do not remove the filterwhile the appliance oper-ates. Do not clean the drainpump if the wa
7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Clean the filter under the water tapand put
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur
• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.WARNING!Deactivate the appliance beforeyou do the chec
Problem Possible cause Possible solutionThe programmedoes not start.The mains plug is notconnected in the mainssocket.Put in the mains plug. Blow out
After the check, activate the appliance.The programme continues from thepoint of interruption.If the problem occurs again, contact theservice centre.I
5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th
13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
ENGLISH 33
34www.aeg.com
ENGLISH 35
www.aeg.com/shop132929561-A-502012
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1200 rpm1
4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th
Commentaires sur ces manuels