Aeg-Electrolux L60260TL Manuel d'utilisateur

L 60260 TLL 60060 TLEN WASHING MACHINE USER MANUAL

WASHING PROGRAMMESProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCottons95° - ColdWhite and colouredcotton with normalsoi

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsCurtains40° - ColdSet this programmeto wash curtains. Itadds automatically

Programme1)Energy consump-tion (KWh)2)Water consump-tion (litre)2)Easy iron 60°C 0.50 55Delicates 40°C 0.50 48Wool 40°C 0.50 50Spin 0.05 /Drain 0.01 /

LOADING THE LAUNDRYA1.Open the lid of the appliance.2.Push the button A (depending onmodel). The drum opens automatical-ly.3.Put the laundry. Make sur

SETTING AND STARTING A PROGRAMME1.Turn the programme knob.2.The indicator of button 4 flasheswith red colour.3.The indicators of the default tempera-t

AT THE END OF PROGRAMME• The appliance stops automatically.• The acoustic signals operate.•In the display comes on.• The indicator of the Start/Pause

DETERGENTS AND ADDITIVES• Only use detergents and additives spe-cially made for washing machines.• Do not mix different types of deter-gents.• To help

CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.DESCALINGThe water we use contains limescale. If itbecomes

1.Open the drain filter door.2.Put a container below the recess ofthe drain filter to collect the waterthat flows out. Turn the filter until it isvert

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with a stiffbrush or a towel.90˚6.Install again the inlet hose. Make suret

CONTENTS4 SAFETY INFORMATION6 PRODUCT DESCRIPTION6 ACCESSORIES7 CONTROL PANEL10 WASHING PROGRAMMES12 BEFORE FIRST USE12 USING THE APPLIANCE13 LOADING

TROUBLESHOOTINGThe start of the appliance does not occuror it stops during operation.First try to find a solution to the problem(refer to the table).

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

INSTALLATIONUNPACKING1.Remove the external film. If necessa-ry, use a cutter.2.Remove the polystyrene packagingmaterials.3.Tilt the appliance backward

8.Remove the power supply cable andthe drain hose from the hose holders.219.Remove the three bolts.11210.Remove the plastic piece.11.Replace the plast

WARNING!Remove all the packaging and thetransit bolts before you install theappliance.We recommend that you keep thepackaging and the transit bolts fo

THE INLET HOSE90˚1.Connect the hose to the appliance.Loose the ring nut to set it in the cor-rect position.2.Connect the water inlet hose to thecold w

WATER DRAINAGEThere are different procedures to connectthe drain hose:With the plastic hose guide. • On the edge of a sink.• Make sure that the plasti

• Directly to a built-in drain pipe in theroom wall and tighten it with a clip.You can extend the drain hose tomaximum 400 cm. Contact theservice cent

ENGLISH29

FOR PERFECT RESULTSThank you for choosing this AEG product. We have created it to give youimpeccable performance for many years, with innovative techn

30www.aeg.com

ENGLISH31

www.aeg.com/shop 108616701-B-072012

SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environmen

• Make sure not to cause damage to thewater hoses.• Do not connect the appliance to newpipes or pipes not used for a long time.Let the water flow for

PRODUCT DESCRIPTION2315469810117121Control panel2Lid3Lid handle4Filter access door5Lever to move the appliance6Adjustable feet7Rating plate8Mains cabl

CONTROL PANEL4567891 2 31On/Off button2Programme knob3Display4Start/Pause button 5Delay start button 6Time saving button 7Extra rinse button 8Spin but

The display shows:A • The programme timeWhen the programme starts, the time decreases with steps of 1 minute.• The delay startWhen you press the delay

TEMPERATURE BUTTON 9Press button 9 to change the defaulttemperature.CHILD LOCK FUNCTIONThis function prevents children to playwith the control panel.•