L 6027 FL EN User manual
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsSynthetics60° - ColdSynthetic or mixedfabric items with nor-mal level of s
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsJeans60° - ColdAll items in jeans.Jersey made itemswith hi-tech materi-als
Programmes Load(Kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approxi-mate pro-grammeduration(minutes)Remainingmoisture(%)1)Cottons 40°C7 0.80
2.Put the laundry in the drum, oneitem at a time. Shake the items be-fore you put them in the appliance.Make sure not to put too much laun-dry in the
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
5.Press button 4 to start the pro-gramme. The indicator of button 4is on with red colour.The drain pump can operate fora short time when the appliance
• The door lock symbol goes off.•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving functi
• Do not mix different types of deter-gents.• To help the environment, do not usemore than the correct quantity of de-tergent.• Obey the instructions
• Set the hottest cotton wash pro-gramme• Use a correct quantity of powder de-tergent with biological properties.After each wash, keep the door open f
5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.11.7 Drain pumpRegularly examine the drainpump and make sure that it i
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
6.Remove fluff and objects from thepump.7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Cle
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta
Problem Possible cause Possible solutionThe spin phasedoes not operate.The spin phase is off. Set the spin programme. The filter of the drainpump is
Problem Possible cause Possible solution You did not remove thestubborn stains beforeyou wash the laundry.Use special products to removethe stubborn
4.Remove the internal film.5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindt
9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three bolts.11.Pull out the plastic spacers.12.Put the plastic
13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
20O20O20O45O45O45O• Connect the other end of the inlethose to the back of the appliance.Turn the inlet hose only left or right.Loose the ring nut to s
• To a stand pipe with vent-hole.Refer to the illustration. Directly into adrain pipe at a height of not less than60 cm (23.6”) and not more than 100c
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
13.6 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t
ENGLISH 31
www.aeg.com/shop132929231-A-262012
2.1 Installation• Remove all the packaging and thetransit bolts.• Keep the transit bolts. When youmove the appliance again you mustblock the drum.• Do
2.3 DisposalWARNING!Risk of injury or suffocation.• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove th
4. PRODUCT DESCRIPTION1 2 35674810119121Worktop2Detergent dispenser3Control panel4Door handle5Rating plate6Drain pump7Feet for the appliance level8Wat
5. CONTROL PANEL1 2 34567891On/Off button2Programme knob3Display4Start/Pause button5Delay Start button6Time Save button7Extra Rinse button8Spin button
The display shows:A • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the dela
5.9 Temperature button 9Press button 9 to change the defaulttemperature.= cold water5.10 Acoustic signals functionYou can hear the acoustic signals wh
Commentaires sur ces manuels