L 70478 FLL 70678 FLEN User manual
Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsExtra Leise95° - ColdWhite and colouredcotton with normalsoil.max. 7 kgWas
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsGardinen40° - ColdSet this programmeto wash curtains. Itadds automatically
6) Set this programme to decrease the time and the consumption of energy and water.7) According to regulation 1061/2010, these programmes are respecti
Programmes Load(kg)Energyconsump-tion(kWh)Watercon-sump-tion (li-tre)Approxi-matepro-grammeduration(mi-nutes)Remain-ingmois-ture(%)1)L 70478FLRemain-i
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.9.4
When you activate the applianceagain, the display show the endof the last set programme. Turnthe programme knob to set anew cycle.• Remove the laundry
• If you use liquid detergents, do not setthe prewash phase.• If your appliance has not the deter-gent dispenser with the flap device,add the liquid d
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
11.4 Door sealRegularly examine the seal and removeall objects from the inner part.11.5 DrumRegularly examine the drum to preventlimescale and rust pa
11.7 Drain pumpRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum ca
7.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.218.Clean the filter under the water tapand put
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur
• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.WARNING!Deactivate the appliance beforeyou do the chec
Problem Possible cause Possible solutionThe programmedoes not start.The mains plug is notconnected in the mainssocket.Put in the mains plug. Blow out
After the check, activate the appliance.The programme continues from thepoint of interruption.If the problem occurs again, contact theservice centre.I
5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th
13.2 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
ENGLISH 33
34www.aeg.com
ENGLISH 35
www.aeg.com/shop132933741-A-432012
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1400 rpm
4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
–Press button 1 to activate the ap-pliance again.– Set again the washing programmeand all possible options.• After 5 minutes from the end of thewashin
D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th
Commentaires sur ces manuels