LAVAMAT 82470 BI EN User manual
tons 4 and 5 until the symbol comeson or disappears from the display.5.4 EXTRA RINSE optionWith this function you can keep the extrarinse function p
ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsLana/Seda 40° - ColdMax. load 2 kgMachine washable wool as
ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsTejidos Gruesos60° - ColdMax. load 3 kgAll items in jeans.
The water temperature of the washing phase may differ from the temperature de-clared for the selected programme.7. CONSUMPTION VALUESThe data of this
9. DAILY USE9.1 Loading the laundry1.Open the appliance door.2.Put the laundry in the drum, oneitem at a time. Shake the items be-fore you put them in
Always obey the instructions that you find on the packaging of the de-tergent products.9.3 Setting the programme(knob 1 )Turn the programme selector d
To scroll all the available options, pressthe button 4. The relative symbol ap-pears on the display and starts blinking.For the compatibility among th
and the message Err is displayed for afew seconds.9.13 SETTING THE DELAYSTART (button 9)Before you start the programme, if youwish to delay the start
9.18 At the end of theprogrammeThe appliance stops automatically, thelight of button 8 goes off. A blinking appears on the display and the acousticsig
• Obey the instructions that you find onthe on packaging of these products.• Use the correct products for the typeand colour of the fabric, the pro-gr
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
11.3 Door sealRegularly examine the seal and removeall objects from the inner part.11.4 DrumRegularly examine the drum to preventlimescale and rust pa
11.6 Drain pumpThe pump should be inspected regularlyand particularly if:• the appliance does not empty and/orspin;• the appliance makes an unusual no
7.Check carefully whether the pumpimpeller rotates (it rotates jerkily). Ifit doesn’t rotate, please contactyour Service Centre.8.Put the cap back on
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur
cal Service Centre, please carry out thechecks listed below.During machine operation it is possiblethat the yellow pilot light of button 8blinks, one
Problem Possible cause/SolutionThe applince does notempty and/or does notspin:The drain hose is squashed or kinked. • Check the drain hose connection.
Problem Possible cause/SolutionThe appliance vibratesor is noisy:You have not removed the transit bolts and packing.• Check the correct installation o
13. INSTALLATION13.1 Unpacking1.Use the gloves. Remove the externalfilm. If necessary, use a cutter.2.Remove the cardboard top.3.Remove the polystyren
6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure
12.Put the plastic caps in the holes.You can find these caps in the usermanual bag.WARNING!Remove all the packaging andthe transit bolts before you in
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
13.3 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co
With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the
You can extend the drain hose tomaximum 400 cm. Contact theservice centre for the other drainhose and the extension.14.1 Building in600 mm555 mm596 mm
12• HingesTo mount the hinges it is necessary todrill two holes (dia. 35 mm, depth12.5-14 mm depending on the depthof door furniture) on the inner sid
ABCEDIf the door has to be opened from left toright, invert the position of the plates E ,the magnet D and the plate C. Mountthe counter-magnet D and
ENGLISH 35
www.aeg.com/shop132928571-A-102013
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1400 rpm1
4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
5.1 DisplayCI H G F EA B DATemperature indicator and COLD symbol.BSpin Speed indicator, RINSE HOLD , NIGHT CYCLE - symbols.CProgramme progress d
FThe display shows the following information:• Duration of the selected programme– After setting a programme, the duration is displayed in hours andmi
Commentaires sur ces manuels