Aeg-Electrolux L87685FL Manuel d'utilisateur

L 87485 FLL 87685 FLEN User manual

5.11 Acoustic signals functionYou can hear the acoustic signals when:• You activate the appliance.• You deactivate the appliance.• You press the butto

ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsStrijkvrij - Repas-sage Facile4)Easy Iron60 - 0°Synthetic fabric itemswi

ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsJeans60° - 0°All items in jeans. Jerseymade items with hi-techmaterials.

Steam Refresh Opfrissen - RafraîchirThis cycle removes odours from thelaundry.Steam does not remove animalodours.Cotton and syntheticitemsup to 1.5 Kg

Pro-grammesLoad(kg)Energyconsump-tion (kWh)Waterconsump-tion (litre)Approxi-matepro-grammeduration(minutes)Remain-ingmoisture(%)1)L 87485FLRemain-ingm

5.Use the correct quantity of deter-gent and additives.6.Set and start the correct programmefor the type of laundry and soil.8.1 Loading the laundry1.

Flap for powder or liquid detergentTurn it (up or down) in the correct position to use powder or liq-uid detergent.Always obey the instructions that y

8.3 Setting and starting aprogramme1.Turn the programme knob. The rela-ted programme indicator comes on.2.The indicator of button 4 flasheswith red co

If the temperature and level ofthe water in the drum are toohigh, the door lock symbol stayson and you cannot open thedoor. To open the door do theste

– Use a washing bag to wash smallitems.• A very small load can cause balanceproblems with the spin phase. If thisoccurs, adjust manually the items int

CONTENTS1. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNI

find on the packaging of the manufactur-er.Do this separately from the laundrywash.10.2 External cleaningClean the appliance only with soap andwarm wa

3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the dispe

3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

11. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

1. SAFETY INSTRUCTIONSBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the enviro

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

13. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

ENGLISH 33

34www.aeg.com

ENGLISH 35

www.aeg.com/shop132940952-A-212012

• Do not install and connect a damagedappliance.• Make sure to remove all packagingand transport bolts.• Make sure that the mains plug is dis-connecte

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 8 kgSpin speed Maximum 1400 rpm

4. CONTROL PANELTemp.°CT/min.Start/PauzeDépart/PauseExtraSpoelenRinçage +Tijd BesparenGain deTempsStartuitstelDépartDifféréVlekkenTaches/VoorwasPrélav

5.3 Display 3A HJKLC D E F GBIThe display shows:AThe temperature of the set programmeCold waterBThe spin speed of the set programmeNo Spin symbol1)Rin

FYou cannot open the appliance door when the symbol ison.You can open the door only when the symbol goes off.If the programme is completed but the sym

The indicator bar is fully filled when you set to the maxi-mum number of rinses.LThe Stain symbol comes on when you activate the function.The Prewash