L 88489 FL2 EN User manual
• The display shows this message for some secondswhen:– You cannot set a function with the washing pro-gramme.– You try to change the washing programm
The indicator bar is fully filled when you set the maxi-mum number of rinses.MThe Stain symbol comes on when you activate thefunction.The Prewash symb
5.11 Acoustic signals functionYou can hear the acoustic signals when:• You activate the appliance.• You deactivate the appliance.• You press the butto
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctions Easy Iron4)60 - 0°Synthetic fabrics withnormal soil.max. load 4 kgWashR
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsOutdoor40° - 0°Waterproof, sportsand outdoor items.Do not use any fabric
STEAM PROGRAMMESProgramme1)Type of load Maxload Steam RefreshThis cycle removes odours from the laundry.Steam does not remove animalodours.Cotton an
7. CONSUMPTION VALUESAt programme start the display shows the duration programme for the max-imum load capacity.During the washing phase the programme
2.Put a small quantity of detergent inthe main wash compartment of thedetergent dispenser. Set and start aprogramme for cotton at the highesttemperatu
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.3 Filling the detergent and a
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
9.5 Cancel the delay start1.Press button 4 . The related indica-tor flashes.2.Press button 5 again and again un-til the display shows 0’.3.Press butto
• Keep the door ajar, to prevent mildewand odours.• Close the water tap.The washing programme iscompleted, but there is water in thedrum:– The drum tu
add the liquid detergents with a dos-ing ball.10.4 Water hardnessIf the water hardness in your area is highor moderate, we recommend that youuse a wat
11.4 Door sealRegularly examine the seal and removeall objects from the inner part.11.5 DrumRegularly examine the drum to preventlimescale and rust pa
11.7 Drain pumpRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum ca
7.Remove fluff and objects from thepump.8.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.129.Cle
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur
• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.• - The anti-flood device is on.WARNING!Deactivate the
Problem Possible cause Possible solution The filter of the drainpump is blocked.Clean the filter of the drainpump. Refer to 'Care and clean-ing&
Problem Possible cause Possible solution You did not remove thestubborn stains beforeyou wash the laundry.Use special products to removethe stubborn
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from
127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f
WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
www.aeg.com/shop132926711-A-082013
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro
4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
StainPrewash9Spin reduction button10Temperature button5.1 AUTO Off button 1Press this button to activate or deacti-vate the appliance. A tune sounds w
CPrewash phaseWashing phaseRinses phaseSpin phaseThe phase symbols• When a programme is set, all the symbols of the phases relatedto the programme com
Commentaires sur ces manuels